Out of Stock

Contact us for a price



(Scotland & Ireland will incure an additional
shipping surcharge, for a
complete shipping cost to these locations please
contact us)
With its hydraulic retraction, working with the BX-42RS is a real pleasure. There is no pushing, pushing, etc. with this model; the 2 large feed rollers do this alone. The speed of the feed rollers can be varied continuously. This is important in order to match the feed speed to the diameter of the shredded material. Smaller diameters can be drawn in faster than larger diameters. Should the feed still block, the feed can be put into reverse mode via the large bracket on the funnel. Furthermore, the feed can also be switched off using this bracket. The supply takes place via the tractor hydraulics; What is needed is a pressure flow and a pressure-free return or a double-acting control unit. A liter capacity of approx. 10 l / min is required to operate the feed rollers. sufficient.

The BX-42 RS model is the latest version of the BX shredder, which has double-sided suspension of the feed rollers and a reinforced feed hopper.

The wood chipper is delivered complete with PTO. A shear pin is installed on one side of the PTO shaft, which for safety reasons serves as a predetermined breaking point in the event of blockages or overloads. Larger tractors with more than 100 HP can be used without any problems. You should have at least 30 HP of engine power available. The PTO speed must be 540 rpm. be.

The filling funnel has an opening of 51 x 51 cm at the top; in the lower area the opening measures 10.2 x 25.4 cm. A maximum of 10 cm in diameter can be shredded. Many competitors give the maximum shredded material diameter equal to the dimensions of the lower filling opening, but this information is unrealistic and can trigger the safety mechanism in the PTO. Softer woods can be shredded with dimensions of up to 15 cm wide; such diameters are usually processed into firewood and are not chopped.

The processing of the BX-42RS is very solid; The material thicknesses of the sheets used are 10 and 5 mm in the load-bearing area, 2 mm on the funnels and on non-load-bearing parts.

The funnel can be easily folded up for transport and secured with a split pin.

The machine is very easy to maintain; so you can open the entire flywheel cover by loosening just one screw and have access to the 4 cutting blades. These cutting knives have blades on both sides so that they can be easily rotated if necessary. The flywheel has a dead weight of 50 kg and has attached wings, which generate the very strong pull through which the shredded material is ultimately blown out through the discharge funnel. Clogging of the shredder is almost impossible due to this very strong draft.

The discharge funnel has a height of 152 cm (plus the lower link lift) and can be rotated 360 degrees. This means that the shredded material can easily be filled onto higher trailers or directly into big bags. The ejection angle can also be changed. The BX-42RS throws the shredded material up to 6 meters!

The shredder is designed for 3-point suspension and can be used from Cat. I.

Technical specifications:

  • Tractor output: min. 30 HP
  • Hydr. Flow rate: from 10 l / min.
  • Recording: 3-point from cat. I
  • PTO: included
  • RPM: 540
  • Number of knives: 4 knives, 1 shear bar
  • Flywheel diameter: 63.5 cm
  • Feed: hydraulic (via tractor hydraulics)
  • Dimensions: 102x107x152 cm (LxHxW)
  • Width at the bottom of the funnel: approx. 155 cm
  • Packaging: 132x85x136 cm (LxWxH)
  • Weight m. Packaging: 320 kg
  • Weight: approx. 290 kg

Please note that all Jansen equipment is sold subject to these conditions in addition to our standard T&C's.